UNO ZERO

Sanitizing matte plastic paint. ZERO bacteria and ZERO mold. With antibacterial activity certificate: it incorporates silver ions that give the dry paint film already applied, resistance to the growth of bacteria (reduction of 99.9% in 24 hours) and molds. ZERO emissions and ZERO odor: with A + low emission certificate, it also has a very low concentration of volatile organic compounds VOC: 0.2 g / l, 150 times less than required for its category. It does not emit an odor when applied, it allows you to enable spaces immediately without discomfort. This product contributes to LEED®, BREEAM® and VERDE certifications.
Finish
Mate
Performance
12 - 14 m²/L
Drying time
1h
Formats
12L 15L 4L 0.75L 1L

applications

  • Concrete
  • Brick
  • Dripping effect
  • Plaster
  • Cement mortars
  • Indoors/Outdoors
  • Sports centres
  • indoor swimming pools
  • changing rooms
  • etc.
  • Food processing plants
  • supermarkets
  • etc
  • Clinics
  • hospitals
  • homes for the elderly
  • schools
  • nurseries
  • etc.
  • Because of its low emission and low odour properties
  • it is particularly recommended for indoor use.
  • Walls and ceilings
  • Drywall (gypsum plasterboard): fibreboard

How to apply?

  • Painting brush
  • Roller
  • Air-less gun

Colors

White BL base Tintometric System Colours.
- Remove the product until perfectly homogeneous.
- Apply on clean and dry surfaces, removing dirt with soapy water. In the case of extreme dirt, it is advisable to use degreasing agents or cleaning detergents.
- Apply in accordance with requirements marked in the attached application table.
- Do not apply the product at temperatures below 5º nor on surfaces exposed to strong sunshine.
- Maintain good ventilation conditions during the drying time.
- Do not apply whilst the relative humidity is above 80%.
- For a perfect finish we recommend applying with a spray gun, but if you do use a roller it should be one designed for varnishing.
- Do not wash for the first 24 days.
- Clean tools with water immediately after use.
- Never apply it outdoors if there is an imminent risk of rain, and avoid excessively wet days.
- For spraying with Airless equipment, use 15 to 23 inch nozzles, pressure ? 150 bar.
Cement and concrete mortars:
1. Wait until fully set (min. 30 days).
2. Clean any efflorescence with a jet washer.
3. Neutralize alkaline surfaces.
4. Sand polished surfaces to create a rougher surface.
5. Clean the surface to remove foreign products.
6. Set crumbly substrates with Fixer Emulsion or Fijamont.
7. Fill in defects in the substrate (see family 6)

Plaster, plaster-covered brick:
1. Wait until it is completely dry (max. 20% humidity).
2. Clean the surface to remove foreign products.
3. Clean any efflorescence with a jet washer.
4. Regulate surface absorption with sealer, fixer, or a diluted coat of the same product
5. Sand polished surfaces to create a rougher surface
6. Set crumbly substrates with Fixer Emulsion or Fijamont.
7. Fill in defects in the substrate (see family 6)

Plasterboard partition walls:
1. Carry out a general sanding of the joints and putty fixing areas.
2. Then, clean them to ensure the substrate is free of dust, grease and other contaminants.
3. For application on coloured boards that tend to generate stains, apply Montoplac Stain-Resistant Sealer.

Certifications

Downloads

I´m interested in this product
I´m interested in this product

Confirm the product and your contact information to be able to inform you and advise you in a personalized way.

Readily available stock

Gestión automatizada de las ubicaciones y las existencias de los productos.

Perfect orders

Los pedidos son preparados mediante radiofrecuencia reduciendo los errores en su preparación a 0.

Warehouse management

Ubicación automática de los productos en el almacén mediantes transelevador.

Fast loading

8 loading docks for 24-ton trucks.

Our own transport

Flota propia de camiones de reparto preparados para transporte ADR.

We are always close by

Cadena de tiendas propia y suministro a puntos de venta en toda España.